Switch Security: Management and Implementation (2.2)
When you take a new switch out of the box, the first thing the network engineer does is secure the switch and assign it an IP address, subnet mask, and default gateway so the switch can be managed from a remote location. Learning the different methods used to secure a switch is important. Also important is learning the types of attacks that can be launched on, toward, or through a switch. By understanding the attacks and the available tools and countermeasures, a technician can be better prepared to secure the switch and make use of the tools and security commands.Secure Remote Access (2.2.1)
There are different methods that can be used to secure a switch including Telnet and SSH. Telnet has already been covered, but SSH is a much better method used to securely manage the switch from a remote location.SSH Operation (2.2.1.1)
Secure Shell (SSH) is a protocol that provides a secure (encrypted) management connection to a remote device. SSH should replace Telnet for management connections. Telnet is an older protocol that uses insecure plaintext transmission of both the login authentication (username and password) and the data transmitted between the communicating devices. SSH provides security for remote connections by providing strong encryption when a device is authenticated (username and password) and also for the transmitted data between the communicating devices. SSH is assigned to TCP port 22. Telnet is assigned to TCP port 23.Look at the online course, and select the first graphic to see how an attacker can monitor packets using a product such as Wireshark. A Telnet stream can be targeted to capture the username and password.
In the following output, you can see how the attacker can capture the username and password of the administrator from the plaintext Telnet session.
........... User Access verification username: ..................P.........vt100..BBoobb . Password: cisco . R1> eenn . Password: class . R1#Click on the third graphic in the online course to see a Wireshark view of an SSH session. The attacker can track the session using the IP address of the administrator device.
However, if a Wireshark capture is made on the SSH session, the fourth graphic in the online course shows how the username and password are encrypted.
To enable SSH on a Catalyst 2960 switch, the switch must be using a version of the IOS software including cryptographic (encrypted) features and capabilities. In the following output, use the show version command on the switch to see which IOS the switch is currently running, and IOS filename that includes the combination “k9” supports cryptographic (encrypted) features and capabilities.
S1> show version
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M),
Version 15.0(@)SE, RELEASE SOFTWARE (fc1)
<output omitted>
Configuring SSH (2.2.1.2)
Before configuring SSH, the switch must be minimally configured with a unique hostname and the correct network connectivity settings.- Verify SSH support: Use the show ip ssh command to verify that the switch supports SSH. If the switch is not running an IOS that supports cryptographic features, this command is unrecognized.
- Configure the IP domain: Configure the IP domain name of the network using the ip domain-name domain-name global configuration mode command. In Figure 2-12, the domain-name value is cisco.com.
Figure 2-12 Configure SSH for Remote Management
- Generate RSA key pairs: Generating an RSA key pair automatically enables SSH. Use the crypto key generate rsa global configuration mode command to enable the SSH server on the switch and generate an RSA key pair. When generating RSA keys, the administrator is prompted to enter a modulus length. Cisco recommends a minimum modulus size of 1024 bits (refer to the sample configuration in Figure 2-12). A longer modulus length is more secure, but it takes longer to generate and use.
Activity 2.2.1.2: Configure SSHVerifying SSH (2.2.1.3)
On a PC, an SSH client, such as PuTTY, is used to connect to an SSH server. For the examples in Figures 2-16 to 2-18, the following have been configured:- SSH enabled on switch S1
- Interface VLAN 99 (SVI) with IP address 172.17.99.11 on switch S1
- PC1 with IP address 172.17.99.21
Figure 2-13 Configure PuTTY with SSH Client Connection Parameters
Figure 2-14 Remote Management SSH Connection
Figure 2-15 Verify SSH Status and Settings
Packet Tracer Activity 2.2.1.4: Configuring SSHSecurity Concerns in LANs (2.2.2)
Wired LANs are a common source of attack because so much information can be gained about the wired network using free downloadable tools. By examining downloaded frames, attackers can determine IP addresses of network devices, protocols being used, valid server names and IP addresses, etc. With this information an attacker can launch further attacks or even insert a rogue device. This section introduces the types of attacks and countermeasures to be performed on a wired LAN.Common Security Attacks: MAC Address Flooding (2.2.2.1)
Basic switch security does not stop malicious attacks. Security is a layered process that is essentially never complete. The more aware networking professionals within an organization are regarding security attacks and the dangers they pose, the better. Some types of security attacks are described here, but the details of how some of these attacks work are beyond the scope of this course. More detailed information is found in the CCNA WAN Protocols course and the CCNA Security course.MAC Address Flooding
All Catalyst switch models use a MAC address table for Layer 2 switching. The MAC address table in a switch contains the MAC addresses associated with each physical port and the associated VLAN for each port. As a frame arrives on a switch port, the source MAC address is recorded in the MAC address table. The switch then examines the received destination MAC address and looks in the MAC address table to see if it contains the destination MAC address. If an entry already exists for the destination MAC address, the switch forwards the frame to the correct port. If the destination MAC address does not exist in the MAC address table, the switch floods the frame out of every port on the switch, except the port where the frame was received.The MAC address flooding behavior of a switch for unknown addresses can be used to attack a switch. This type of attack is called a MAC address table overflow attack. MAC address table overflow attacks are sometimes referred to as MAC flooding attacks and CAM table overflow attacks. The following figures show how this type of attack works.
In Figure 2-16, host A sends traffic to host B. The switch receives the frames and looks up the destination MAC address in its MAC address table. If the switch cannot find the destination MAC in the MAC address table, the switch then copies the frame and floods (broadcasts) it out of every switch port, except the port where it was received.
Figure 2-16 MAC Address Flooding - Switch Floods Frame for Unknown MACHost C also receives the frame from host A to host B, but because the destination MAC address of that frame is host B, host C drops that frame.
Figure 2-17 MAC Address Flooding - Switch Records MAC Address
Figure 2-18 MAC Address Flooding - Switch Uses MAC Address Table to Forward TrafficAs shown in Figure 2-19, an attacker at host C can send frames with fake, randomly-generated source and destination MAC addresses to the switch. The switch updates the MAC address table with the information in the fake frames. When the MAC address table is full of fake MAC addresses, the switch enters into what is known as fail-open mode. In this mode, the switch broadcasts all frames to all machines on the network. As a result, the attacker can see all of the frames.
Figure 2-19 MAC Address Flooding Attack - Attacker Launches AttackAs shown in Figure 2-20, as long as the MAC address table on the switch remains full, the switch broadcasts all received frames out of every port except the ingress port. In this example, frames sent from host A to host B are also broadcast out of port 3 on the switch and seen by the attacker at host C.
Figure 2-20 MAC Address Flooding Attack - Attacker Sees BroadcastsCommon Security Attacks: DHCP Spoofing (2.2.2.2)
DHCP is the protocol that automatically assigns a host a valid IP address out of a DHCP pool. DHCP has always been the main protocol used within industry for allocating clients IP addresses. Two types of DHCP attacks can be performed against a switched network: DHCP starvation attacks and DHCP spoofing, as shown in Figure 2-21.
Figure 2-21 DHCP Spoofing and Starvation AttackIn DHCP spoofing attacks, an attacker configures a fake DHCP server on the network to issue DHCP addresses to clients. The normal reason for this attack is to force the clients to use false Domain Name System (DNS) or Windows Internet Naming Service (WINS) servers and to make the clients use the attacker, or a machine under the control of the attacker, as their default gateway.
DHCP starvation is often used before a DHCP spoofing attack to deny service to the legitimate DHCP server, making it easier to introduce a fake DHCP server into the network.
To mitigate DHCP attacks, use the DHCP snooping and port security features on the Cisco Catalyst switches. These features are covered in a later topic.
Common Security Attacks: Leveraging CDP (2.2.2.3)
The Cisco Discovery Protocol (CDP) is a proprietary protocol that all Cisco devices can be configured to use. CDP discovers other Cisco devices that are directly connected, which allows the devices to auto-configure their connection. In some cases, this simplifies configuration and connectivity.By default, most Cisco routers and switches have CDP enabled on all ports. CDP information is sent in periodic, unencrypted broadcasts. This information is updated locally in the CDP database of each device. Even though CDP is a Layer 2 protocol, all Cisco devices can use CDP to communicate and share device information with an adjacent Cisco device; however, this information cannot be shared beyond a single, adjacent Cisco device.
CDP contains information about the device, such as the IP address, software version, platform, capabilities, and the native VLAN. This information can be used by an attacker to find ways to attack the network, typically in the form of a DoS attack.
Figure 2-22 shows a portion of a Wireshark capture showing the contents of a CDP packet. The Cisco IOS software version discovered via CDP, in particular, would allow the attacker to determine whether there were any security vulnerabilities specific to that particular version of IOS. Also, because CDP is not authenticated, an attacker could craft bogus CDP packets and send them to a directly-connected Cisco device.
Figure 2-22 Wireshark CDP Packet CaptureTelnet Attacks
The Telnet protocol is insecure and can be used by an attacker to gain remote access to a Cisco network device. There are tools available that allow an attacker to launch a brute force password-cracking attack against the vty lines on the switch.Brute Force Password Attack
A brute force password attack tries to crack a password on another device. The first phase of a brute force password attack starts with the attacker using a list of common passwords and a program designed to try to establish a Telnet session using each word on the dictionary list. If the password is not discovered by the first phase, a second phase begins. In the second phase of a brute force attack, the attacker uses a program that creates sequential character combinations in an attempt to guess the password. Given enough time, a brute force password attack can crack almost all passwords used.To mitigate against brute force password attacks, use strong passwords that are changed frequently. A strong password should have a mix of uppercase and lowercase letters and should include numerals and symbols (special characters). Access to the vty lines can also be limited using an access control list (ACL) that designates what IP address(es) are allowed access to the vty lines.
Telnet DoS Attack
Telnet can also be used to launch a DoS attack. In a Telnet DoS attack, the attacker exploits a flaw in the Telnet server software running on the switch that renders the Telnet service unavailable. This sort of attack prevents an administrator from remotely accessing switch management functions. This can be combined with other direct attacks on the network as part of a coordinated attempt to prevent the network administrator from accessing core devices during the breach.Vulnerabilities in the Telnet service that permit DoS attacks to occur are usually addressed in security patches that are included in newer Cisco IOS revisions.
Activity 2.2.2.4: Common Security AttacksSecurity Best Practices (2.2.3)
With so many devices being attached to the wired network, network security is even more important today. Security starts the moment you take a network device, such as a switch, out of the box for the first time. Now that some of the common attacks have been covered, next is what a network administrator can do to protect and counteract those attacks.Best Practices (2.2.3.1)
Defending your network against attack requires vigilance and education. The following are best practices for securing a network:- Develop a written security policy for the organization.
- Shut down unused services and ports.
- Use strong passwords and change them often.
- Control physical access to devices.
- Avoid using standard insecure HTTP websites, especially for login screens; instead use the more secure HTTPS.
- Perform backups and test the backed up files on a regular basis.
- Educate employees about social engineering attacks, and develop policies to validate identities over the phone, via email, and in person.
- Encrypt and password-protect sensitive data.
- Implement security hardware and software, such as firewalls.
- Keep software up-to-date by installing security patches weekly or daily, if possible.
Network Security Tools and Testing (2.2.3.2)
Network security tools help a network administrator test a network for weaknesses. Some tools allow an administrator to assume the role of an attacker. Using one of these tools, an administrator can launch an attack against the network and audit the results to determine how to adjust security policies to mitigate those types of attacks. Security auditing and penetration testing are two basic functions that network security tools perform.Network security testing techniques may be manually initiated by the administrator. Other tests are highly automated. Regardless of the type of testing, the staff that sets up and conducts the security testing should have extensive security and networking knowledge. This includes expertise in the following areas:
- Network security
- Firewalls
- Intrusion prevention systems
- Operating systems
- Programming
- Networking protocols (such as TCP/IP)
Network Security Audits (2.2.3.3)
Network security tools allow a network administrator to perform a security audit of a network. A security audit reveals the type of information an attacker can gather simply by monitoring network traffic.For example, network security auditing tools allow an administrator to flood the MAC address table with fictitious MAC addresses. This is followed by an audit of the switch ports as the switch starts flooding traffic out of all ports. During the audit, the legitimate MAC address mappings are aged out and replaced with fictitious MAC address mappings. This determines which ports are compromised and not correctly configured to prevent this type of attack.
Timing is an important factor in performing the audit successfully. Different switches support varying numbers of MAC addresses in their MAC table. It can be difficult to determine the ideal amount of spoofed MAC addresses to send to the switch. A network administrator also has to contend with the age-out period of the MAC address table. If the spoofed MAC addresses start to age out while performing a network audit, valid MAC addresses start to populate the MAC address table, and limiting the data that can be monitored with a network auditing tool.
Network security tools can also be used for penetration testing against a network. Penetration testing is a simulated attack against the network to determine how vulnerable it would be in a real attack. This allows a network administrator to identify weaknesses within the configuration of networking devices and make changes to make the devices more resilient to attacks. There are numerous attacks that an administrator can perform, and most tool suites come with extensive documentation detailing the syntax needed to execute the desired attack.
Because penetration tests can have adverse effects on the network, they are carried out under very controlled conditions, following documented procedures detailed in a comprehensive network security policy. An off-line test bed network that mimics the actual production network is the ideal. The test bed network can be used by networking staff to perform network penetration tests.
Switch Port Security (2.2.4)
Port security is the process of enabling specific commands on switch ports to protect against unauthorized wired devices being attached to the network. An easy way for an intruder to gain access to a corporate network is to plug into an unused Ethernet jack or to unplug an authorized device and use that connector. Cisco provides ways to protect against such behavior.Secure Unused Ports (2.2.4.1)
The first step in port security is to be aware of ports that are not currently being used on the switch.Disable Unused Ports
A simple method that many administrators use to help secure the network from unauthorized access is to disable all unused ports on a switch. For example, if a Catalyst 2960 switch has 24 ports and there are three Fast Ethernet connections in use, it is good practice to disable the 21 unused ports. Navigate to each unused port and issue the Cisco IOS shutdown command. If a port later on needs to be reactivated, it can be enabled with the no shutdown command. Figure 2-23 shows partial output for this configuration.
Figure 2-23 Disable Unused Switch PortsSwitch(config)# interface range type module/first-number – last-numberThe process of enabling and disabling ports can be time-consuming, but it enhances security on the network and is well worth the effort.
DHCP Snooping (2.2.4.2)
DHCP snooping is a Cisco Catalyst feature that determines which devices attached to switch ports can respond to DHCP requests. DHCP snooping can be used to prevent unauthorized DHCP messages that contain information such as IP address-related data being provided to legitimate network devices.As part of the DHCP configuration process, switch ports can be identified as trusted and untrusted. Trusted ports can source any type of DHCP message; untrusted ports can source DHCP requests only. This configuration protects the network from someone attacking a device by acting as a rogue DHCP server. Trusted ports host a DHCP server or can be an uplink toward the DHCP server. If a rogue device on an untrusted port attempts to send a DHCP response packet into the network, the port is shut down. This feature can be coupled with DHCP options in which switch information, such as the port ID of the DHCP request, can be inserted into the DHCP request packet.
As shown in Figures 2-24 and 2-25, untrusted ports are those not explicitly configured as trusted. A DHCP binding table is built for untrusted ports. Each entry contains a client MAC address, IP address, lease time, binding type, VLAN number, and port ID recorded as clients make DHCP requests. The table is then used to filter subsequent DHCP traffic. From a DHCP snooping perspective, untrusted access ports should not send any DHCP server responses.
Figure 2-24 DHCP Snooping Operation
Figure 2-25 DHCP Snooping Configuration
Step 2. Enable DHCP snooping for specific VLANs using the ip dhcp snooping vlan number command.
Step 3. Define ports as trusted at the interface level by defining the trusted ports using the ip dhcp snooping trust command.
Optional Limit the rate at which an attacker can continually send bogus DHCP
Step 4. requests through untrusted ports to the DHCP server using the ip dhcp snooping limit rate rate command.
Port Security: Operation (2.2.4.3)
All switch ports (interfaces) should be secured before the switch is deployed for production use. One way to secure ports is by implementing a feature called port security. Cisco port security limits the number of valid MAC addresses allowed on a port. The MAC addresses of legitimate devices are allowed access, while other MAC addresses are denied.Port Security
Port security can be configured to allow one or more MAC addresses. If the number of MAC addresses allowed on the port is limited to one, then only the device with that specific MAC address can successfully connect to the port.If a port is configured as a secure port and the maximum number of MAC addresses is reached, any additional attempts to connect by unknown MAC addresses will generate a security violation.
Secure MAC Address Types
There are a number of ways to configure port security. The type of secure address is based on the configuration and includes:- Static secure MAC addresses: MAC addresses that are manually configured on a port by using the switchport port-security mac-address mac-address interface configuration mode command. MAC addresses configured in this way are stored in the address table and are added to the running configuration on the switch.
- Dynamic secure MAC addresses: MAC addresses that are dynamically learned and stored only in the address table. MAC addresses configured in this way are removed when the switch restarts.
- Sticky secure MAC addresses: MAC addresses that can be dynamically learned or manually configured stored in the address table, and added to the running configuration.
Sticky Secure MAC addresses
To configure an interface to convert dynamically learned MAC addresses to sticky secure MAC addresses and add them to the running configuration, you must enable sticky learning. Sticky learning is enabled on an interface by using the switchport port-security mac-address sticky interface configuration mode command.When this command is entered, the switch converts all dynamically learned MAC addresses, including those that were dynamically learned before sticky learning was enabled, to sticky secure MAC addresses. All sticky secure MAC addresses are added to the address table and to the running configuration.
Sticky secure MAC addresses can also be manually defined. When sticky secure MAC addresses are configured by using the switchport port-security mac-address sticky mac-address interface configuration mode command, all specified addresses are added to the address table and the running configuration.
If the sticky secure MAC addresses are saved to the startup configuration file, then when the switch restarts or the interface shuts down, the interface does not need to relearn the addresses. If the sticky secure addresses are not saved, they will be lost.
If sticky learning is disabled by using the no switchport port-security mac-address sticky interface configuration mode command, the sticky secure MAC addresses remain part of the address table but are removed from the running configuration.
The following list shows the characteristics of sticky secure MAC addresses.
- Learned dynamically, converted to sticky secure MAC addresses stored in the running-config.
- Removed from the running-config if port security is disabled.
- Lost when the switch reboots (power cycled).
- Saving sticky secure MAC addresses in the startup-config makes them permanent, and the switch retains them after a reboot.
- Disabling sticky learning converts sticky MAC addresses to dynamic secure addresses and removes them from the running-config.
Port Security: Violation Modes (2.2.4.4)
It is a security violation when either of these situations occurs:- The maximum number of secure MAC addresses have been added to the address table for that interface, and a station whose MAC address is not in the address table attempts to access the interface.
- An address learned or configured on one secure interface is seen on another secure interface in the same VLAN.
- Protect: When the number of secure MAC addresses reaches the limit allowed on the port, packets with unknown source addresses are dropped until a sufficient number of secure MAC addresses are removed or the number of maximum allowable addresses is increased. There is no notification that a security violation has occurred.
- Restrict: When the number of secure MAC addresses reaches the limit allowed on the port, packets with unknown source addresses are dropped until a sufficient number of secure MAC addresses are removed or the number of maximum allowable addresses is increased. In this mode, there is a notification that a security violation has occurred.
- Shutdown: In this (default) violation mode, a port security violation causes the interface to immediately become error-disabled and turns off the port LED. It increments the violation counter. When a secure port is in the error-disabled state, it can be brought out of this state by entering the shutdown and no shutdown interface configuration mode commands.
Table 2-9 Security Violations Modes
| Violation Mode | Forwards Traffic | Sends Syslog Message | Displays Error Message | Increases Violation Counter | Shuts Down Port |
| Protect | No | No | No | No | No |
| Restrict | No | Yes | No | Yes | No |
| Shutdown | No | No | No | Yes | Yes |
- A station with MAC address that is not in the address table attempts to access the interface when the table is full.
- An address is being used on two secure interfaces in the same VLAN.
Port Security: Configuring (2.2.4.5)
Table 2-10 summarizes the default port security configuration on a Cisco Catalyst switch.Table 2-10 Port Security Default Settings
| Feature | Default Setting |
| Port security | Disabled on a port |
| Maximum number of secure MAC addresses | 1 |
| Violation mode | Shutdown. The port shuts down when the maximum number of secure MAC addresses is exceeded. |
| Sticky address learning | Disabled |
Figure 2-26 Port Security Configuration TopologyTable 2-11 Cisco Switch IOS CLI Commands for Dynamic Port Security
| Specify the interface to be configured for port security. | S1(config)# interface fastethernet 0/18 |
| Set the interface mode to access. | S1(config-if)# switchport mode access |
| Enable port security on the interface. | S1(config-if)# switchport port-security |
Table 2-12 Cisco Switch IOS CLI Commands for Sticky Port Security
| Specify the interface to be configured for port security. | S1(config)# interface fastethernet 0/19 |
| Set the interface mode to access. | S1(config-if)# switchport mode access |
| Enable port security on the interface. | S1(config-if)# switchport port-security |
| Set the maximum number of secure addresses allowed on the port. | S1(config-if)# switchport port-security maximum 50 |
| Enable sticky learning. | S1(config-if)# switchport port-security mac-address sticky |
Port Security: Verifying (2.2.4.6)
Many students make the mistake of forgetting to enable port security before doing the specific port security options. For any configuration step, verification is important. It is especially important when configuring port security.Verify Port Security
After configuring port security on a switch, check each interface to verify that the port security is set correctly, and check to ensure that the static MAC addresses have been configured correctly.Verify Port Security Settings
To display port security settings for the switch or for the specified interface, use the show port-security [interface interface-id] command. The output for the dynamic port security configuration is shown as follows. By default, there is one MAC address allowed on this port.S1# show port-security interface fastethernet 0/18
Port Security : Enabled
Port Status : Secure-up
Violation Mode : Shutdown
Aging Time : 0 mins
Aging Type : Absolute
SecureStatic Address Aging : Disabled
Maximum MAC Addresses : 1
Total MAC Addresses : 1
Configured MAC Addresses : 0
Sticky MAC Addresses : 0
Last Source Address:Vlan : 0025.83e6.4b01:1
Security Violation Count : 0
Taking a look at the port after the configuration has been applied
shows the values for the sticky port security settings. The maximum
number of addresses is set to 50 as configured.S1# show port-security interface fastethernet 0/19 Port Security : Enabled Port Status : Secure-up Violation Mode : Shutdown Aging Time : 0 mins Aging Type : Absolute SecureStatic Address Aging : DisabledSticky MAC addresses are added to the MAC address table and to the running configuration. As shown in the output, the sticky MAC address for PC2 has been automatically added to the running configuration for S1.Maximum MAC Addresses : 50Total MAC Addresses : 1 Configured MAC Addresses : 0Sticky MAC Addresses : 1Last Source Address:Vlan : 0025.83e6.4b02:1 Security Violation Count : 0
S1# show run | begin FastEthernet 0/19
interface FastEthernet0/19
switchport mode access
switchport port-security
switchport port-security maximum 50
switchport port-security mac-address sticky
switchport port-security sticky 0025.83e6.4b02
Verify Secure MAC Addresses
To display all secure MAC addresses configured on all switch interfaces, or on a specified interface with aging information for each, use the show port-security address command. As shown in the output, the secure MAC addresses are listed along with the types.S1# show port-security address
Secure Mac Address Table
---------------------------------------------------------
Vlan Mac Address Type Ports Remaining Age
(mins)
---- ----------- ---- ----- ---------------
1 0025.83e6.4b01 SecureDynamic Fa0/18 -
1 0025.83e6.4b02 SecureSticky Fa0/19 -
---------------------------------------------------------
Ports in Error Disabled State (2.2.4.7)
When a port is configured with port security, a violation can cause the port to become error disabled. When a port is error disabled, it is effectively shut down and no traffic is sent or received on that port. A series of port security related messages display on the console as shown.Sep 20 06:44:54.966: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/18, putting Fa0/18 in err-disable state Sep 20 06:44:54.966: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 000c.292b.4c75 on port FastEthernet0/18. Sep 20 06:44:53.973: %LINEPROTO-5-PPDOWN: Line protocol on Interface FastEthernet0/18, changed state to down Sep 20 06:44:56.971: %LINK-3-UPDOWN: Interface FastEthernet0/18, changed state to downAnother indication that a port security violation has occurred is that the switch port LED will change to orange. The show interfaces command identifies the port status as err-disabled as shown in the following output. The output of the show port-security interface command now shows the port status as secure-shutdown. Because the port security violation mode is set to shutdown, the port with the security violation goes to the error disabled state.
S1# show interfaces fastethernet 0/18 status Port Name Status Vlan Duplex Speed Type Fa0/18 err-disabled 1 auto auto 10/100BaseTX S1# show port-security interface fastethernet 0/18 Port Security : Enabled Port Status : Secure-shutdown Violation Mode : Shutdown Aging Time : 0 mins Aging Type : Absolute SecureStatic Address Aging : Disabled Maximum MAC Addresses : 1 Total MAC Addresses : 0 Configured MAC Addresses : 0 Sticky MAC Addresses : 0 Last Source Address:Vlan : 000c.292b.4c75:1 Security Violation Count : 1The administrator should determine what caused the security violation before re-enabling the port. If an unauthorized device is connected to a secure port, the port should not be re-enabled until the security threat is eliminated. To re-enable the port, use the shutdown interface configuration mode command. Then, use the no shutdown interface configuration command to make the port operational, as shown in the following output.
S1(config)# interface FastEthernet 0/18 S1(config-if)# shutdown Sep 20 06:57:28.532: %LINK-5-CHANGED: Interface FastEthernet0/18, changed state to administratively down S1(config-if)# no shutdown Sep 20 06:57:48.186: %LINK-3-UPDOWN: Interface FastEthernet0/18, changed state to up Sep 20 06:57:49.193: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/18, changed state to up
Network Time Protocol (NTP) (2.2.4.8)
Having the correct time within networks is important. Correct time stamps are required to accurately track network events such as security violations. Additionally, clock synchronization is critical for the correct interpretation of events within syslog data files as well as for digital certificates.Network Time Protocol (NTP) is a protocol that is used to synchronize the clocks of computer systems over packet-switched, variable-latency data networks. NTP allows network devices to synchronize their time settings with an NTP server. A group of NTP clients that obtain time and date information from a single source will have more consistent time settings.
A secure method of providing clocking for the network is for network administrators to implement their own private network master clocks, synchronized to UTC, using satellite or radio. However, if network administrators do not want to implement their own master clocks because of cost or other reasons, other clock sources are available on the Internet. NTP can get the correct time from an internal or external time source including the following:
- Local master clock
- Master clock on the Internet
- GPS or atomic clock
Figure 2-27 Configuring NTPFigure 2-28 displays the verification of NTP. To display the status of NTP associations, use the show ntp associations command in privileged EXEC mode. This command will indicate the IP address of any peer devices that are synchronized to this peer, statically configured peers, and stratum number. The show ntp status user EXEC command can be used to display such information as the NTP synchronization status, the peer that the device is synchronized to, and in which NTP strata the device is functioning.
Figure 2-28 Verifying NTP Packet Tracer Activity 2.2.4.9: Configuring Switch Port Security Packet Tracer Activity 2.2.4.10: Troubleshooting Switch Port Security
Lab 2.2.4.11: Configuring Switch Security Features- Part 1: Set Up the Topology and Initialize Devices
- Part 2: Configure Basic Device Settings and Verify Connectivity
- Part 3: Configure and Verify SSH Access on S1
- Part 4: Configure and Verify Security Features on S1
ReplyDeletethanks for sharing this content.
CCTV security systems
cctv suppliers in dubai
Switching Concepts And Configuration ~ Lonethought'S >>>>> Download Now
ReplyDelete>>>>> Download Full
Switching Concepts And Configuration ~ Lonethought'S >>>>> Download LINK
>>>>> Download Now
Switching Concepts And Configuration ~ Lonethought'S >>>>> Download Full
>>>>> Download LINK